基于树莓派的智能家居系统

JAY.LIN 收录于未分类

2025-01-01 约 1471 字预计阅读 3 分钟

https://bing.ee123.net/img/rand?artid=108329382

基于树莓派的智能家居系统

提示：文章写完后，目录可以自动生成，如何生成可参考右边的帮助文档

文章目录

概述

使用树莓派、Arduino、语音模块、红外模块实现对家用空调进行控制
树莓派与Arduino进行TCP协议通信
树莓派与语音模块，Arduino与红外模块都进行串口通信

一、硬件组成

图1.树莓派

图2.Arduino

图3.语音模块

图4.红外模块

二、软件

图1.Arduino开发环境

图2.树莓派系统

图3.串口调试助手

三.获取空调遥控器红外编码

1、将红外模块与TTL串口相连接，并插入电脑USB口（注意管脚接线正确）

将需要被解码的空调遥控器按键对着红外模块按下，即在串口上返回所需要的解码数据（注意波特率，这里默认为115200）。

获取到红外编码后，将编码全部复制，以十六进制发送，红外模块对着空调，查看空调是否有反应。

四.树莓派与Arduino进行TCP协议通信

(1) 将Arduino做为服务端

#include <ESP8266WiFi.h>

char ssid[] = "1004"; /_ wifi 账号_/
char passwd[] = "13609618951"; /_ 密码_/
int port = 8888; /_ 端口号_/
WiFiServer server(port); /_ 设置服务器端口_/

const byte open_data[] = { /_ 空调红外开码_/
0xFE, 0xFD, 0x03, 0x85, 0x01, 0xC3, 0x40, 0x39, 0x3F, 0x3B, 0x3D, 0x39, 0x3F, 0xAA, 0x3D, 0x3B, 0x3D, 0x39, 0x3F,
0xAA, 0x3C, 0x39, 0x3F, 0xAA, 0x3D, 0x39, 0x3F, 0x3C, 0x3C, 0xAA, 0x3F, 0x37, 0x3F, 0x39, 0x41, 0x37, 0x3F, 0x39,
0x3F, 0x3C, 0x3C, 0x39, 0x3F, 0x39, 0x3F, 0x3C, 0x3D, 0x38, 0x40, 0x38, 0x40, 0x3B, 0x3D, 0x39, 0x3F, 0x39, 0x3F,
0x39, 0x3F, 0x39, 0x3F, 0x39, 0x3F, 0xAA, 0x3F, 0x37, 0x3F, 0xAA, 0x3D, 0x38, 0x3F, 0x3C, 0x3C, 0xAA, 0x3D, 0x39,
0x3F, 0x07, 0xD4, 0x3F, 0x3A, 0x3F, 0x3B, 0x3D, 0x39, 0x3F, 0x3B, 0x3D, 0x3B, 0x3D, 0x3C, 0x3F, 0x39, 0x3C, 0x39,
0x3F, 0x39, 0x40, 0x38, 0x40, 0x38, 0x40, 0x38, 0x40, 0x3B, 0x3D, 0x39, 0x3F, 0x39, 0x3F, 0x39, 0x3F, 0x39, 0x3F,
0x3A, 0x41, 0x37, 0x3F, 0x39, 0x3F, 0x39, 0x3F, 0x39, 0x3F, 0x39, 0x3F, 0x3C, 0x3C, 0x39, 0x40, 0x38, 0x40, 0x39,
0x3F, 0x39, 0x3F, 0xAA, 0x3D, 0xA9, 0x3D, 0x39, 0x3F, 0xAA, 0x3D, 0x0F, 0xA9, 0x03, 0x83, 0x01, 0xC3, 0x3F, 0x3C,
0x3C, 0x3C, 0x3D, 0x3B, 0x3C, 0xAA, 0x3D, 0x39, 0x3F, 0x3C, 0x3C, 0xAA, 0x3D, 0x39, 0x3F, 0xAA, 0x3C, 0x3C, 0x3C,
0x39, 0x40, 0xA9, 0x3D, 0x3B, 0x3D, 0x3C, 0x3C, 0x39, 0x3F, 0x39, 0x3F, 0x39, 0x3F, 0x3A, 0x3E, 0x3C, 0x3C, 0x3C,
0x3D, 0x38, 0x40, 0x39, 0x3F, 0x39, 0x3F, 0x39, 0x3E, 0x39, 0x40, 0x38, 0x40, 0x3B, 0x3D, 0x39, 0x3F, 0xAA, 0x3D,
0xA9, 0x3D, 0xAA, 0x3C, 0x39, 0x3F, 0x3A, 0x3F, 0xA9, 0x3D, 0x39, 0x3F, 0x07, 0xD4, 0x40, 0x39, 0x3F, 0x39, 0x3F,
0x3B, 0x3D, 0x3B, 0x3F, 0x3A, 0x3C, 0x39, 0x3F, 0x3C, 0x3C, 0x39, 0x3F, 0x39, 0x3F, 0x39, 0x40, 0x38, 0x3F, 0x3C,
0x3D, 0x3B, 0x3D, 0x3B, 0x3D, 0x3B, 0x3D, 0x39, 0x3F, 0x39, 0x3F, 0x39, 0x40, 0x38, 0x40, 0x39, 0x3F, 0x3B, 0x3D,
0x39, 0x3F, 0x39, 0x3F, 0x3B, 0x3D, 0xAA, 0x3D, 0xAA, 0x3C, 0x3C, 0x3C, 0x39, 0x3F, 0xAA, 0x3D, 0xAA, 0x3C, 0x39, 0x40, 0xA9, 0x3D, 0xFF
};

const byte close_data[] = { /_ 空调红外关码_/
0xFE, 0xFD, 0x03, 0x85, 0x01, 0xC1, 0x41, 0x37, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42,
0xA7, 0x40, 0x36, 0x42, 0xA7, 0x3F, 0x37, 0x41, 0x37, 0x41, 0xA8, 0x3F, 0x36, 0x42, 0x37, 0x41, 0x37, 0x41, 0x37,
0x41, 0x37, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x37, 0x41, 0x37, 0x41, 0x37, 0x42, 0x36, 0x42, 0x36, 0x42,
0x36, 0x41, 0x37, 0x42, 0x36, 0x42, 0xA7, 0x3F, 0x37, 0x42, 0xA7, 0x3F, 0x37, 0x41, 0x37, 0x41, 0xA8, 0x3F, 0x36,
0x42, 0x07, 0xD3, 0x41, 0x37, 0x41, 0x37, 0x41, 0x37, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x37, 0x41, 0x37,
0x41, 0x37, 0x41, 0x37, 0x42, 0x36, 0x42, 0x36, 0x42, 0x37, 0x41, 0x37, 0x41, 0x37, 0x41, 0x37, 0x42, 0x36, 0x42,
0x36, 0x42, 0x36, 0x42, 0x37, 0x41, 0x37, 0x41, 0x37, 0x41, 0x37, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36,
0x42, 0x36, 0x42, 0xA7, 0x40, 0xA7, 0x3F, 0x37, 0x41, 0x37, 0x42, 0x0F, 0xA8, 0x03, 0x85, 0x01, 0xC1, 0x42, 0x36,
0x42, 0x36, 0x42, 0x36, 0x42, 0x37, 0x41, 0x37, 0x41, 0x36, 0x42, 0xA8, 0x3F, 0x36, 0x42, 0xA7, 0x3F, 0x37, 0x42,
0x36, 0x42, 0xA7, 0x3F, 0x37, 0x41, 0x37, 0x41, 0x37, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x37, 0x41, 0x37,
0x41, 0x37, 0x41, 0x37, 0x41, 0x37, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x37, 0x41, 0xA8, 0x3F,
0xA7, 0x3F, 0xA8, 0x3F, 0x36, 0x42, 0x36, 0x42, 0xA7, 0x3F, 0x37, 0x42, 0x07, 0xD2, 0x41, 0x37, 0x41, 0x37, 0x42,
0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x37, 0x41, 0x37, 0x41, 0x37, 0x41, 0x37, 0x42, 0x36,
0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0x37, 0x41, 0x37, 0x41, 0x37, 0x41, 0x37, 0x42, 0x36, 0x42,
0x36, 0x42, 0x36, 0x42, 0x36, 0x42, 0xA7, 0x40, 0xA7, 0x3F, 0x37, 0x41, 0x37, 0x41, 0xA8, 0x3F, 0xA7, 0x40, 0x36, 0x42, 0x36, 0x42, 0xFF
};

void initWifi() /_ 建立 Wifi 网络模块_/
{
WiFi.mode(WIFI_STA); /_ 设置为 STA 模式_/
WiFi.begin(ssid, passwd); /_输入 wifi 账号和密码_/

    while(WiFi.status() != WL_CONNECTED){
        Serial.print(".");
        delay(500);
    }

    Serial.println(WiFi.localIP());		/* 打印IP地址*/
    delay(500);

}

void setup()
{
Serial.begin(115200); /_ 设置波特率_/
initWifi(); /_ 初始化网络_/

}

void loop()
{
char cmd;
WiFiClient client = server.available(); /_ 设置为服务端_/
server.begin(); /_ 服务端初始化_/

    while(client.connected()){          /* 检测是否连接*/
        while(client.available() > 0){  /* 如果串口中有数据*/

            cmd = client.read();        /* 将串口中的数据传给cmd*/
            //Serial.println(cmd);      /* 打印cmd*/

            if(cmd == '1'){
             // Serial.println("1111111111"); 
                Serial.write(open_data, (sizeof(open_data) / sizeof(open_data[0])));
            }
            if(cmd == '2'){
             // Serial.println("22222222");
                Serial.write(close_data, (sizeof(close_data) / sizeof(close_data[0])));
            }
        }
    }

}

(2) 树莓派作为客户端

#include<stdio.h>
#include<string.h>
#include<sys/types.h>
#include<sys/socket.h>
#include<netinet/in.h>
#include<arpa/inet.h>
#include<stdlib.h>
#include<unistd.h>
#include<wiringSerial.h>
#include<unistd.h>
#include<string.h>
#include<wiringPi.h>

int main(int argc, char *argv[])
{
int fd;
int c_fd;
int ret;
char cmd[128] = {'\0'};
char a = '1';
char b = '2';

    if(argc != 3){
        printf("input params error!\n");
        exit(0);
    }

    wiringPiSetup();        /* 硬件初始化，使用wiringPi引脚*/
    fd = serialOpen("/dev/ttyAMA0", 9600);      /* 打开串口*/
    if(fd == -1) {
        perror("open failed");
        exit(-1);
    }

    /* 创建网络套接字*/
    c_fd = socket(AF_INET, SOCK_STREAM, 0);
    if(c_fd == -1){
        perror("socket failed!\n");
        exit(-1);
    }

    /* 建立连接*/
    struct sockaddr_in addr;
    memset(&addr, 0, sizeof(addr));

    addr.sin_family = AF_INET;                  /* 设置IP协议*/
    addr.sin_port = htons(atoi(argv[2]));       /* 传递端口号，从网络（大端）到主机（小端）*/
    inet_aton(argv[1], &addr.sin_addr);         /* 传递IP地址*/

    ret = connect(c_fd, (struct sockaddr *)&addr, sizeof(struct sockaddr));
    if(ret == -1) {
        perror("connect wemos failed!\n");
        exit(-1);
    }else{
        printf("connected successfully\n");
    }

    while(1){

        read(fd, cmd, sizeof(cmd));     /* 读取语音模块发送的指令*/

        if(strstr(cmd,"open")){
            printf("accept open\n");
            write(c_fd, &a, sizeof(char));
        }

        if(strstr(cmd,"close")){
            printf("accept close\n");
            write(c_fd, &b, sizeof(char));
        }

        printf("cmd:%s",cmd);
    	memset(cmd, '\0', sizeof(cmd) / sizeof(char));
        serialFlush(fd);                /* 刷新缓冲区数据*/
        delay(200);
    }

    return 0;

}