H3C-交换机配置静态聚合trunkaccess模式
H3C 交换机配置静态聚合(trunk/access)模式
目标：
H3C 交换机配置静态聚合(trunk/access)模式
硬件配置：
1.三层核心交换机：S7005e
2.二层交换机：S5120 v2
S7005e过程：
创建vlan （如果已经存在可跳过此步骤）
[H3C]vlan 20
设置名称（Test可自行更改）
[H3C-vlan20]name Test
返回系统视图
[H3C-vlan20]qu
进入vlan 20
[H3C]interface vlan 20
修改vlan标签（Test可自行更改）
[H3C-Vlan-interface20]description Test
vlan添加IP地址（192.168.200.1网关地址可自行修改）
（24子网掩码，可自行修改（也可255.255.255.0））
（（192.168.200.1 24）等同（192.168.200.1 255.255.255.0））
[H3C-Vlan-interface20]ip address 192.168.200.1 24
返回系统视图
[H3C-Vlan-interface20]qu
配置聚合组 （组ID：20（可自行修改））
[H3C]interface Bridge-Aggregation 20
修改汇聚组标签
[H3C-Bridge-Aggregation20]description Test
修改聚合组端口信息与vlan配置
根据聚合模式选择（trunk/access）
[H3C-Bridge-Aggregation20]port link-type access
添加端口到vlan（两种模式只能选择一种不能共存）
access模式添加
[H3C-Bridge-Aggregation20]port access vlan 20
trunk模式添加（两种模式只能选择一种不能共存）
[H3C-Bridge-Aggregation20]port trunk permit vlan 20
返回系统视图
[H3C-Bridge-Aggregation20]qu
#设置需要汇聚的物理端口 （只演示一个端口的配置，多个端口请自行复制粘贴）
进入端口视图
[H3C]interface GigabitEthernet 1/0/1
端口模式配置与汇聚端口相同（命令执行是相同）
[H3C-GigabitEthernet1/0/1]port link-type access
[H3C-GigabitEthernet1/0/1]port access vlan 20
端口加入汇聚组（ID：20）
[H3C-GigabitEthernet1/0/1]port link-aggregation group 20
在把需要汇聚的端口都配置好，自此三层核心的交换机就已经完成（汇聚组ID：20）的配置，如需更多的汇聚组请参考此列。
查看全部汇聚组信息
]display link-aggregation verbose
显示：
Loadsharing Type: Shar – Loadsharing, NonS – Non-Loadsharing
Port: A – Auto
Port Status: S – Selected, U – Unselected, I – Individual
Flags: A – LACP_Activity, B – LACP_Timeout, C – Aggregation,
D – Synchronization, E – Collecting, F – Distributing,
G – Defaulted, H – Expired
Aggregate Interface: Bridge-Aggregation20 Aggregation Mode: Static （这里也表示为静态） Loadsharing Type: Shar Port Status Priority Oper-Key
GE1/0/1 S 32768 1（S：Static的意思）
GE1/0/2 S 32768 1（S：静态模式）
Aggregate Interface: Route-Aggregation1
Aggregation Mode: Static
Loadsharing Type: Shar
查看汇聚组20的信息
display interface Bridge-Aggregation 20
以下是配置后的端口信息
Bridge-Aggregation20
Current state: UP
IP packet frame type: Ethernet II, hardware address: 1a46-e48a-0100
Description: Test
Bandwidth: 2000000 kbps
2Gbps-speed mode, full-duplex mode
Link speed type is autonegotiation, link duplex type is autonegotiation
PVID: 20
Port link-type: Access
Tagged VLANs: None
Untagged VLANs: 20
Last clearing of counters: Never
Last 300 second input: 0 packets/sec 0 bytes/sec 0%
Last 300 second output: 0 packets/sec 0 bytes/sec 0%
Input (total): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
Input (normal): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
Input: 0 input errors, 0 runts, 0 giants, 0 throttles
0 CRC, 0 frame, 0 overruns, 0 aborts
0 ignored, 0 parity errors
Output (total): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
—- More —-
S5120 v2过程：
前言：相对于三层核心的配置，二层交换机就显的简单很多
对于access模式的只需要把对应汇聚组的端口修改到相同的vlan ID，然后创建汇聚组
加入对应的端口，在新的H3C设备种已经不需要在二层设置access模式，默认模式下也可以自动识别，只需要将其他端口加入。
查看汇聚组20的信息
display interface Bridge-Aggregation 20
以下是配置后的端口信息
Bridge-Aggregation20
Current state: UP
IP packet frame type: Ethernet II, hardware address: 1a77-315c-0200
Description: Test
Bandwidth: 2000000 kbps
2Gbps-speed mode, full-duplex mode
Link speed type is autonegotiation, link duplex type is autonegotiation
PVID: 20
Port link-type: Access
Tagged VLANs: None
Untagged VLANs: 20
Last clearing of counters: Never
Last 300 second input: 0 packets/sec 0 bytes/sec 0%
Last 300 second output: 0 packets/sec 0 bytes/sec 0%
Input (total): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
Input (normal): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
Input: 0 input errors, 0 runts, 0 giants, 0 throttles
0 CRC, 0 frame, 0 overruns, 0 aborts
0 ignored, 0 parity errors
Output (total): 0 packets, 0 bytes
0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses
—- More —-